banner



How To Secure Plywood To Windows

Unless all your commercial building's windows are fitted with hurricane shutters, you might find yourself using plywood to encompass vulnerable glass before the side by side big storm.

Boarding windows with plywood for hurricane harm mitigation is an affordable, readily-available option, simply it's but effective if done properly.

Proceed reading to learn some of the superlative recommendations from the experts on how to board up windows correctly for the best storm damage protection.

Recommendations on Boarding Windows with Plywood for Hurricanes

How To Install Plywood for Hurricane Protection: Preparation

  • Utilize 5/8-inch CDX plywood boards (outside class)
  • Pre cut boards to encompass all windows
  • Screw stainless steel hanger bolts into the framing every 16 inches
  • Drill matching holes through boards
  • Pigment boards
  • Label boards with the openings they're for

Earlier hurricane flavour even arrives, you should purchase enough boards of v/eight-inch CDX plywood to encompass all your building's windows. CDX plywood is meant for exterior uses, and then it volition hold up amend over time after repeated exposure to weather.

Measure all your windows and pre cut the boards to fit into each one. It's best if yous tin fit the boards within the window frames, otherwise cut them so at that place's a 4-inch overlap on all sides of the windows.

At present that you accept your boards cut, information technology's a corking idea to install bolts effectually the frames of windows to brand hanging the boards easier during storm season.

Drill pilot holes into the framing studs every xvi inches and screw three-inch stainless steel hanger bolts 2 inches deep into the holes. Annotation that for physical block buildings, you lot'll accept to drill holes into the masonry 2- 3 inches from the edges of the window frames.

If you lot can't prepare your windows for boards with bolts, y'all can use screws to set the boards over the glass when information technology's fourth dimension to install them, every bit long as the edifice is wood-framed.

Measure and mark the location of the bolts along the edges of the boards. Drill holes simply big enough that the boards slide snuggly onto the bolts.

And so, since you can reuse these boards over multiple hurricane seasons, it'due south a proficient idea to prime and paint the surfaces and edges of the plywood sheets with exterior-course paint to make them even more than weather resistant.

Finally, label ane side or border of each sheet with the opening it'south meant for, and then you lot don't waste time figuring information technology out when you're preparing your property for a storm.

How To Install Plywood for Hurricane Protection: Installation

  • Install boards when a hurricane lookout is issued
  • Get at to the lowest degree i other person to help you put up plywood
  • Secure boards over bolts with washers and nuts
  • Use galvanized pan-caput screws if you didn't pre-install bolts

Hurricane experts country that you should offset boarding up your belongings as soon as a hurricane watch is issued for your area, which occurs 48 hours earlier hurricane weather is expected to brainstorm.

Your boards should already be securely in place past the time a hurricane warning is issued 36 hours before the storm is expected.

Installing the boards is at least a two-person chore, and then become an employee or someone else you tin count on to help you lot become the job done.

If you already installed hanger bolts around your edifice'southward window frames and drilled matching holes in your boards, all you have to do is slide the plywood sheets onto the bolts. Then, slide a washer over each commodities and screw wing nuts tightly over the washers to secure the boards.

If yous didn't prepare your windows with bolts, utilize a cordless drill or bear on driver to drive galvanized pan-head screws every 12-18 inches through the overlapping edges of the boards into framing studs below.

Paradigm via https://www.rona.ca/

These types of screws take flat-bottomed heads, then they won't sink into the plywood and potentially weaken the boards. Make sure to apply screws that are long plenty for them to go at least two inches into the studs. For instance, 3-inch screws should work.

Now that your boards are hung, safely wait out the storm and do the whole process in reverse to accept them down after information technology passes.

How Do You Protect a Window From a Hurricane Without Plywood?

Though plywood boards can provide sufficient protection for your commercial building'south windows during a hurricane, at that place are a number of reasons yous should consider other, more permanent solutions.

Disadvantages of boarding windows:

  • Requires much preparation
  • Labor-intensive process
  • Boards accept up lots of storage infinite
  • Blocks out natural light and cuts off visibility
  • Makes businesses await closed and uninviting to clients
  • Accept to lath up windows every fourth dimension there's a hurricane sentry

Hurricane shutters are 1 of the most mutual commercial hurricane mitigation barriers, but they even so aren't perfect. That'south why we highly recommend installing impact-resistant windows to provide permanent, 24-hour protection against storms (and all manner of security threats).

Advantages of hurricane impact windows:

  • Ane-time installation
  • Look and feel like regular windows
  • Don't cake natural light or views
  • Don't hurt the adjourn appeal of businesses
  • Provide 24/7 protection from hurricanes and tropical storms
  • Create barriers against forced entry, burglary, and smash-and-take hold of theft
  • Also protect against vandalism, rioting, and looting

When you want the absolute best hurricane window protection, we recommend choosing ArmorPlast® AP25. These are polycarbonate glazing shields with a glass-like surface hardness and appearance, but the unbreakable strength of polycarbonate.

Final Words on Using Plywood for Hurricane Protection

Subsequently reading the tips in this article, nosotros promise you lot've gained a ameliorate understanding of how to install plywood for hurricane glass protection.

Even though this is a tried-and-truthful method for storm harm mitigation, it does have its disadvantages that make it an impractical solution for many business owners.

For stronger, more permanent, and more than convenient glass protection, consider retrofitting your property's drinking glass doors and windows with impact-resistant polycarbonate panels.

Contact us today or have your local drinking glass contractor give us a call to discuss how you can fortify your commercial building with ArmorPlast® AP25.

Source: https://www.riotglass.com/how-to-install-plywood-for-hurricane/

Posted by: pierremagards.blogspot.com

0 Response to "How To Secure Plywood To Windows"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel